Panel A · Drivers
All 22 drivers with per-round data columns. Use sort buttons (top right) to reorder. My Team, Rival 1 and Rival 2 columns track team composition per round.
Panel B · Constructors
All 11 constructors with per-round data columns. Constructor DNFs derived from driver DNF flags. Risk classification displayed read-only here — edit risk assignments in the Configuration panel.
Panel C · Pre-race Workflow
Unified pre-race workflow. Round status shows as a banner above Step 1. Steps 1–3: setup (create round, upload thresholds, upload BBF & F1FT). Step 4: run the Blend Optimiser (4A), set the decision blend (4B) and Run z5z (4C) — z5z is always the decision set and Running flips the round to Open. Steps 5–10: the analysis pipeline (Auto Removals → Asset Trends → View Metric Sets → Replacements → Provisional Teams → Finalize Team & Submit). Each step is a collapsible section.
Step 1Create RoundAdd a new round (status flips: No New Round → Scheduled). Carries Start Team forward.
Step 2Upload ThresholdsOfficial F1 price-change thresholds — the basis of all simulations (F1FT, BBF and z5z). Upload while Status = Scheduled.
Step 3Upload BBF & F1FT DataBBF + F1FT forecasts. Activates once thresholds are uploaded. Upload while Status = Scheduled.
Step 4z5z Simulation4A: run the Blend Optimiser (Panel F) — tick Done. 4B: set the decision blend (HA / BBF / F1FT). 4C: Run — blends F1FT/BBF, produces z5z, and flips the round to Open. Run while Status = Scheduled.
Step 5Auto Removals & Manual ReviewFull team view with T2–T4 removal ticks (T1 = the existing team, unchanged; its 2X is set here). Run while Status = Open.
Step 6Asset TrendsOne asset: slow HA vs fast SMA-N, DNFs on the zero line. Prep for Step 8 replacements. Available from Scheduled.
Step 7View Metric SetsF1FT / BBF / z5z side by side (read-only) — the reference table for choosing replacements in Step 8. z5z (Step 4) is always the decision set.
Step 8ReplacementsConstructors and drivers sorted by U; price-range filter per table. Run while Status = Open.
Constructors
Drivers
Step 9Provisional TeamsT1 = the existing team (locked except its 2X) · T2–T4 = your provisional teams. Quantitative view: U, xPts, xΔ$, gap to the Top-U team. Run while Status = Open.
Step 10Finalize Team & SubmitFinal judgement: U chart with the noise zone, then compare the teams, tick My Selection, confirm and submit while Status = Open (irreversible).
Panel D · Post-race Workflow
After the race: enter Rival 1 and Rival 2 results, upload U3+U4 actuals (via the Upload button on Panel A or B), then Mark Completed. Marking Completed locks all three teams' data for that round.
Panel E · Rivals
All rivals data in one place. Tab 1 holds the per-round table and round-status management. Tab 2 holds the dual-axis budget & points charts.
Panel F · Analytics — Chips · Circuits · Correlation · z5z Simulator
v4.0 analytics consolidation. Chips (recommendations), Circuits (track characteristics) and Correlation (prediction accuracy) are now tabs in a single panel.
Panel G · Admin
Admin consolidation (renamed from Configuration in v4.6.3). Constructor risk & exposure rules, selection thresholds, rival defaults, chip scoring, plus Status / Data / Debug tabs.
Round Status & Lock Overrides
Data Operations
Historical / Retrospective Data
Upload F1FT / BBF / Thresholds to any PAST round (each prompts for the target round), then backfill z5z where the inputs exist. Backfill never overwrites rounds that already have z5z.
Data Folder
Loading...
Data Uploads
Upload F1FT or BBF forecasts to ANY round (e.g. retrospective BBF for R1–R5). Writes to the source-specific fields; re-applies the round's Step 3 selection if one exists. F1FT auto-detects the round from the filename convention.
Post-race PRICE to any round (official F1F Current Cost).
CODE,Name,Price.F1F season POINTS repopulation — per-round statistics
CODE,Name,R1,R2,… (from F1F). Sets each round's actualPts + the cumulative F1F total. Use once to load/fix R1–R9 history.Migrations & Data Refreshes
Diagnostics & Repair
State inspector output will appear here.